1310nm Outdoor Optical Transmitter

Products > 1310/1550 Optical Transmitter > 1310nm Outdoor Optical Transmitter

1310nm Outdoor Optical Transmitter

Model: WT1310-xxmW
WT1310AGC is a 1310nm direct modulation optical transmitter with high index and AGC function. It adopts high linearity and low chirp DFB laser, builtin predistortion compensation and AGC, APC,

WT1310AGC is a 1310nm direct modulation optical transmitter with high index and AGC function. It adopts high linearity and low chirp DFB laser, builtin predistortion compensation and AGC, APC, ATC closed loop control, which improves the system index obviously. This transmitter enables cost effective optical transmission in the original HFC network and is ideal for any cable system that need to build the Green Field Service.
Summary                                                                       
◇ WT1310 Series field 1310nm laser transmitter is the featured product that  we exploited on many years’ project practice experience, thoroughly solve the engineering problems that some remote areas can not build indoor machinery room
◇ WT-1310 Series field 1310nm laser transmitter adopt high performance water-   proof cast Aluminum housing, high reliable switch supply, strict anti-thunder system and build in large power electronic refrigerator ,which enable equipment to fit the field environment temperature between -40℃~ to 60℃ and ensure it can work long-time and stably in the field sever environment.
Performance Characteristic
◇ Adopt high performance DFB laser with international famous band, narrow Spectrum, good linear and high output power.
◇ Adopts RF power digital automatic process technology designed by ourselves at RF driving part. It can auto-adjust RF driving power according to the input RF signal level and channel number(15~84) to make the C/CSO、C/CTB and C/N in the best condition ,which ensure performance of the whole equipment and make the output level of optical receiver keep the same.
Advanced multi-frequency point pre-distortion technology with GaAs devices optimize
◇ C/CTB and C/CSO value, which are the most important index in CATV system, meanwhile maximize the C/N.
◇ The built-in micro-computer automatic monitor circuit can real-timely and precisely monitor various working condition of optical output power and laser to ensure the stable optical output power and prolong the working life of laser effectively.
◇ Builtin large power semiconductor refrigerator, which can enable the equipment to fit the field environment temperature between -40℃ to +60℃.。

Adopt high performance water-proof cast Aluminum housing, high reliable switch supply, strict anti-thunder system, which ensure the equipment work long-time and stably under the field severe environment.


Technical parameter

Item

Unit

Technical parameter

Output optical power

mw

4

6

8

10

12

14

16

18

20

22

Optical circuit loss

dB

7

9

10

11

11.8

12.5

13

13.6

14

14.4

Optical wavelength

nm

1310±20

Laser type


DFB laser

Optical modulation mode


Direct optical strength modulation

Optical connector type


FC/APC or SC/APC

Frequency range

MHz

47~750/862

RF input lever

dBμV

72 ~ 88

Flatness in band

dB

±0.75

RF input impedance

Ω

75

Input reflecting loss

dB

≥16(47~550)MHz;≥14(550~750/862)MHz

C/N

dB

≥51

C/CTB

dB

≥65

C/CSO

dB

≥60

AGC control range

dB

±8

MGC control range

dB

±8

Supply voltage

V

AC 160V~250V (50 Hz)

Consumption

W

30

Working temperature

-40 ~ +60

Storage temperature

-50 ~ +70

Relative Humidity

%

Max 95%no condensation

Dimension

mm

430(L)× 250(W)× 160(H)


Circuit test condition
Special Notice
The performance parameters of this manual is according to GY/T143-2000<< Network Entry Technical Requirements and Measurements Method of CATV laser Optical Transmitter and Receiver>>, and get it at the following condition.
Test condition:
10KM standard optical fiber, optical attenuator and standard optical receiver make up of test circuit. Set with 59 PAL-D analog TV channel signal at range of 550MHz in the stated condition of circuit loss. Transmitting digital modulation signal at rang of 550MHz~862MHz, when the electricity level (8 MHz bandwidth) of digital signal is 10dB lower  than analog signal of carrier electricity level, input power of optical receiver is-1dBm, measure C/ CTB, C/ CSO, C/ N.