Fujikura fusion splicer FSM-70S

Products > Fujikura fusion splicer > Fujikura fusion splicer FSM-70S

Fujikura fusion splicer FSM-70S

Model: FSM-70S
The Fujikura 70S is a fully ruggedized, core alignment fusion splicer, providing consistent, low loss, splice performance.
The new design streamlines the steps required to complete splices, resulting in greater productivity. "Configurable automation" features allow you to customize the operation of the machine to best suit your particular splicing technique and process.

Features: 
◇ Automated and programmable wind protector
◇14-second automated tube heater 
◇Fully ruggedized for shock, dust and moisture 
◇Li-Ion battery with 200 splices/shrinks per charge
◇5 mm cleave length for splice on connector or small package needs 
◇Sheath clamp or fiber holder operation 
◇On-board training and support videos 
◇Internet software upgrades 
◇Multi-function transit case with integrated workstation

Description
The Fujikura 70S is a fully ruggedized, core alignment fusion splicer, providing consistent, low loss, splice performance.
The new design streamlines the steps required to complete splices, resulting in greater productivity. "Configurable automation" features allow you to customize the operation of the machine to best suit your particular splicing technique and process.
A new programmable "automatic wind protector" closes and begins the splicing process after clamping the fibers in position or pressing the "set" button. Once the splice is completed, not only is the wind protector opened, but one of the sheath clamps, you decide which, is automatically raised making removal of the fibers fast and easy!
Similarly, the "clamshell" design of the tube heater clamps the splice splice protection sleeve and applies heat from both sides which results in a reduced shrink time of just 14 seconds!

SPECIFICATIONS: 

Applicable fibers

Single / SMF (G.652/657), MMF (G.651), DSF (G.653), NZDSF (G.655)

Cladding dia.

80-150um

Cleave length

5mm to 16mm with sheath clamp

Splice mode / heating mode

Total 100 splice modes / 30 heating modes

Splice loss

0.02dB (SM), 0.01dB (MM), 0.04dB (DSF) and

0.04dB (NZDS) Measured by cut-back method relevant to ITU-T and IEC standards.


Attenuation splice function


Intentional high splice loss of 0.1dB to 15dB(0.1dB step)can be made for an in-line fixed attenuator.

Splice time / tube heating time

Typical 7sec with SM / Typical 14sec with FP-03 (60mm) sleeve

Splice result storage

Last 2000 splices

Viewing methods / magnification

2 axis CMOS camera with 4.73” color LCD.

X / Y (320X magnification), or both X and Y simultaneously (200X magnification)

Tension test

1.96 to 2.25N

Applicable protection sleeve

60mm, 40mm and Fujikura micro sleeves

No. of splice / heating per battery full charge

Typical 200 cycles with BTR-09

Electrode life

3000 splices

Size / weight

146W x 159D x 150H (mm) / 2.7kg (including battery)

Operating condition

Altitude : 0 to 5,000m above sea level, Wind : 15m/sec

Temperature : -10 to 50deg C,

Humidity : 0 to 95%RH, non-dew

Resistance features*1

Shock : 76cm (30inch) all surface drop

Dust : Exposure to dust (0.1 to 500um dia Alumina Silicate), IP5X Rain :

H=10mm/hr for 10min, IPX2

Other features

PC software upgrade / data management

Terminals

USB 2.0 (Mini-B type) connector for PC communication.

6-pin Mini-DIN connector for HJS-02 or HJS-03 power supply